Evaboard HIDE (HW Integrated Development Environment)

Lo schema elettrico allegato costituisce uno dei moduli HIDE, si tratta di un processor classe ARM7 della società NXP nella configurazione più semplice.

Tutti i pin del processor (tranne quelli relativi al suo funzionamento di base) sono “portati” sul connettore HIDE e sono tutti “user defined”.

Il modulo contiene al suo interno:

  • possibilita’ di alimentazione remota tramite regolatore DC-DC (12V >>> 3.3V)
  • possibilita’ di programmazione “in-circuit” tramite interfaccia Wiggler 20pins
  • Quarzo per il clock di base a 16MHz
  • Circuito di reset
  • Connettori di I/O
  • Interfaccia RS232
  • Interfaccia HIDE di tipo SPI con velocità da 1 a 4Mbps

La struttura del modulo lo rende estremamente versatile (nessun pin e’ forzato), anche se costringe l’utente a costruirsi outside la sua parte di elettronica.

Il modulo e’ disponibile nel formato 100x160 standard Eurocard o nel formato 100x80, altri formati sono disponibili a richiesta.

Per una maggiore dettaglio sull’ARM7 NXP si rimanda la sito www.nxp.com sezione controllori 32bit ARM7. Di seguito si riporta un estratto delle caratteristiche tecniche:

  • ARM7TDMI-S processor, running at up to 72 MHz
  • Up to 512 kB on-chip Flash Program Memory with In-System

Programming (ISP) and In-Application Programming (IAP) capabilities. Single Flash sector or full-chip erase in 400 ms and 256 bytes programming in 1 ms. Flash program memory is on the ARM local bus for high performance CPU access.

  • Up to 64 kB of SRAM on the ARM local bus for high performance CPU access
  • 16 kB Static RAM for Ethernet interface. Can also be used as general purpose SRAM
  • 8 kB Static RAM for general purpose or USB interface
  • Dual AHB system that provides for simultaneous Ethernet DMA, USB DMA, and program execution from on-chip flash with no contention between those functions. A bus bridge allows the Ethernet DMA to access the other AHB subsystem
  • Advanced Vectored Interrupt Controller, supporting up to 32 vectored interrupts
  • General Purpose DMA controller (GPDMA) on AHB that can be used with the SSP serial interfaces, the I2S port, and the SD/MMC card port, as well as for memory-to-memory transfers
  • Serial Interfaces:
  • - Ethernet MAC with associated DMA controller. These functions reside on an independent AHB bus.
    - USB 2.0 device controller with on-chip PHY and associated DMA controller.
    - Four UARTs with fractional baud rate generation, one with modem control I/O, one with IrDA support, all with FIFO. These reside on the APB bus.
    - SPI controller, residing on the APB bus.
    - Two SSP controllers with FIFO and multi-protocol capabilities. One is an alternate for the SPI port, sharing its interrupt. The SSP controllers can be used with the GPDMA controller and reside on the APB bus.
    - Three I2C interfaces reside on the APB bus. The second and third I2C interfaces are expansion I2C interfaces with standard port pins rather than special open-drain I2C pins.
    - I2S (Inter-IC Sound) interface for digital audio input or output, residing on the APB bus. The I2S interface can be used with the GPDMA.
    - Two CAN channels with Acceptance Filter/FullCAN mode residing on the APB bus.

  • Other APB Peripherals:
  • - Secure Digital (SD) / MultiMediaCard (MMC) memory card interface.
    - Up to 70 (100 pin packages) or 104 (144 pin packages) general purpose I/O pins.
    - 10 bit A/D converter with input multiplexing among 6 pins (100 pin packages) or 8 pins (144 pin packages).
    - 10 bit D/A converter.
    - Four general purpose timers with two capture inputs each and up to four compare output pins each. Each timer block has an external count input.
    - One PWM/Timer block with support for three-phase motor control. The PWM has two external count inputs.
    - Real-Time Clock (RTC) with separate power pin; clock source can be the RTC oscillator or the APB clock.
    - 2 kB Static RAM powered from the RTC power pin, allowing data to be stored when the rest of the chip is powered off.
    - Watchdog Timer. The watchdog timer can be clocked from the internal RC oscillator, the RTC oscillator, or the APB clock.

  • Standard ARM Test/Debug interface for compatibility with existing tools
  • Emulation Trace Module
  • Support for real-time trace
  • Single 3.3 V power supply (3.0 V to 3.6 V)|
  • Three reduced power modes: Idle, Sleep, and Power-down
  • Four external interrupt inputs. In addition every PORT0/2 pin can be configured as an edge sensing interrupt
  • Processor wakeup from Power-down mode via any interrupt able to operate during Power-down mode (includes external interrupts, RTC interrupt, and Ethernet wakeup interrupt)
  • Two independent power domains allow fine tuning of power consumption based on needed features
  • Brownout detect with separate thresholds for interrupt and forced reset
  • On-chip Power On Reset
  • On-chip crystal oscillator with an operating range of 1 MHz to 24 MHz
  • 4 MHz internal RC oscillator that can optionally be used as the system clock. For USB and CAN application, the use of an external clock source is suggested
  • On-chip PLL allows CPU operation up to the maximum CPU rate without the need for a high-frequency crystal. May be run from the main oscillator, the internal RC oscillator, or the RTC oscillator
  • Boundary scan for simplified board testing is available in LPC2364FET100,LPC2368FET100 (TFBGA packages), LPC2377/78, and LPC2388
  • Versatile pin function selections allow more possibilities for using on-chip peripheral functions

SW
Il modulo non possiede periferiche particolari se non l’SPI per la comunicazione su HIDE e la porta seriale per debugging, programmazione e come terminale, per tale ragione non c’e’ uno specifico SW.
Su richiesta possono essere rese disponibili le librerie di sistema tramite le quali l’utente puo’ facilmente programmare il chip senza entrare nei dettagli.

Nella sezione Download scarica NXP_LPC2368_Evaboard HIDE.pdf

Post dal 9 gennaio 2009

Scarica subito una copia gratis

Scrivi un commento

Seguici anche sul tuo Social Network preferito!

Send this to a friend