Accesso alla EEPROM nei micro AVR

ACCESSO ALLA EEPROM NEI MICRO AVR

Scrittura ad un indirizzo specifico

Il listato 1 presenta una routine  per la scrittura in EEPROM ad uno specifico indirizzo. La routine EEWrite assume che in EEdwr vi sia il dato da scrivere, in EEawr e EEawrh rispettivamente la parte bassa e la parte alta dell’indirizzo a cui scrivere. In figura 1 il diagramma di flusso della routine. La routine occupa 9 words (oltre il return) e viene eseguita in 11 cicli (oltre il return) se la EEPROM è pronta.

.include “8515def.inc”
.def      EEdwr    =r16              ;data byte to write to EEPROM
.def      EEawr    =r17              ;address low byte to write to
.def      EEawrh   =r18              ;address high byte to write to
EEWrite:
  sbic    EECR,EEWE        ;if EEWE not clear
  rjmp    EEWrite          ;wait more
  out     EEARH,EEawrh     ;output address high byte, remove if no high byte exists
  out     EEARL,EEawr      ;output address low byte
  out     EEDR,EEdwr       ;output data
  cli                      ;disable global interrupts
  sbi     EECR,EEMWE       ;set master write enable, remove if 90S1200 is used
  sbi     EECR,EEWE        ;set EEPROM Write strobe
                           ;This instruction takes 4 clock cycles since
                           ;it halts the CPU for two clock cycles
  sei                      ;enable global interrupts
  ret
Listato 1
Figura 1. Routine di scrittura ad un indirizzo specifico

Figura 1. Routine di scrittura ad un indirizzo specifico

Lettura da indirizzo  specifico

Nel listato 2 è riportata la routine per la lettura di un dato da uno specifico indirizzo in EEPROM. La parte bassa e la parte alta dell’indirizzo devono essere contenute rispettivamente nei registri EEard ed EEardh. La routine è composta da 6 word e viene eseguita in 7 cicli. Il diagramma di flusso è riportato in figura 2.

.include “8515def.inc”
.def       EEdrd           =r0        ;result data byte
.def       EEard           =r17       ;address low to read from
.def       EEardh          =r18       ;address high to read from
EERead:   
    sbic   EECR,EEWE       ;if EEWE not clear
    rjmp   EERead          ;wait more
    out    EEARH,EEardh    ;output address high byte, remove if no high byte exists
    out    EEARL,EEard     ;output address low byte
    sbi    EECR,EERE       ;set EEPROM Read strobe
                           ;This instruction takes 4 clock cycles since
                           ;it halts the CPU for two clock cycles
    in     EEdrd,EEDR      ;get data
    ret
Listato 2
Figura 2. Routine di lettura da un indirizzo specifico

Figura 2. Routine di lettura da un indirizzo specifico

Scrittura sequenziale

La routine  per la scrittura in  EEPROM  ad indirizzi sequenziali è riportata in figura 3 e il relativo codice nel listato 3. Il registro EEdwr_s deve contenere il dato da scrivere. La routine occupa 12 words e viene eseguita in 15 cicli.

.def        EEwtmp        =r24    ;temporary storage of address low byte
.def        EEwtmph       =r25    ;temporary storage of address high byte
.def        EEdwr_s       =r18    ;data to write
EEWrite_seq:
  sbic     EECR,EEWE      ;if EEWE not clear
  rjmp     EEWrite_seq    ;wait more
  in       EEwtmp,EEARL   ;get address low byte
  in       EEwtmph,EEARH  ;get address high byte, remove if no high byte exists
  adiw     EEwtmp,0x01    ;increment address
  out      EEARL,EEwtmp   ;output address low byte
  out      EEARH,EEwtmph  ;output address byte, remove if no high byte exists
  out      EEDR,EEdwr_s   ;output data
  cli                     ;disable global interrupts
  sbi      EECR,EEMWE     ;set master write enable, remove if 90S1200 is used
  sbi      EECR,EEWE      ;set EEPROM Write strobe
                          ;This instruction takes 4 clock cycles since
                          ;it halts the CPU for two clock cycles
  sei                     ;enable global interrupts
  ret
Listato 3
Figura 3. Scrittura sequenziale in EEPROM

Figura 3. Scrittura sequenziale in EEPROM

Lettura sequenziale

Per la lettura sequenziale di dati dalla EEPROM si può usare la routine di figura 4 il cui codice è riportato nel listato 4. Il dato letto viene posto in EEdrd_s. La routine è composta da 9 words e viene eseguita in 13 cicli.

.def         EErtmp     =r24         ;temporary storage of low address
.def         EErtmph    =r25         ;temporary storage of high address
.def         EEdrd_s    =r0          ;result data byte

EERead_seq:
    sbic EECR,EEWE ;if EEWE not clear
    rjmp EERead_seq       ; wait more
; The above sequence for EEWE = 0 can be skipped if no write is initiated.

; Read sequence
    in   EErtmp,EEARL        ;get address low byte
    in   EErtmph,EEARH       ;get address high byte, remove if no high byte
exists
   adiw  EErtmp,0x01         ;increment address
   out   EEARL,EErtmp        ;output address low byte
   out   EEARH,EErtmph       ;output address high byte, remove if no high
byte exists


   sbi   EECR,EERE ;set EEPROM Read strobe
                              ;This instruction takes 4 clock cycles since
                              ;it halts the CPU for two clock cycles
   in    EEdrd_s,EEDR         ;get data
   ret
Listato 4
Figura 4. Lettura sequenziale in EEPROM

Figura 4. Lettura sequenziale in EEPROM

 

Scarica subito una copia gratis

Una risposta

  1. Avatar photo Maurizio 17 Aprile 2016

Scrivi un commento

Seguici anche sul tuo Social Network preferito!

Send this to a friend